Showing posts with label Tip and Tricks. Show all posts
Showing posts with label Tip and Tricks. Show all posts

Wednesday, September 8, 2010

How to Take Care Your Notebook / Laptop

Keyboard and LCD monitors is the notebook components most prone to damage. For example when water is accidentally doused keyboard or monitor scratched during cleaning. Here are some tips to prevent damage to the components of the notebook LCD monitor and keyboard.

LCD Monitor
1. LCD Hinges
If observed carefully, in the folds between the CPU and LCD monitors have hinges that allow the two components were clenched to each other. Be aware that the burden is heaviest in a notebook on the part of the hinge. Therefore, do not give the beat at the time of opening will activate the monitor when the notebook. Vice versa, do not be too hard to close the monitor when finished using the laptop computer. It is unfortunate that his name not be avoided. Therefore, when a crack occurs, immediately fix the authorized dealer. It was intended that the damage does not propagate to other places.
2. Half price notebook
LCD screen is very thin and easily broken, so treat with care and should not be subject to impact, pressure, abrasion can make it damage. Remember about 50% of the price of notebooks is the price of the LCD screen.
3. LCD Cleaning
Then how about a dusty notebook LCD screen? Should it be silenced? Not forbidden to clean the LCD monitor. With time, the screen will be NB dirty and dusty. You can spray a special liquid into the LCD cleaning cloth and rub the screen slowly. Use a soft cloth and not abusive. Do not spray directly into the surface of the screen because the liquid can be melted down and can damage electronic circuits. Do not use plastic or glass cleaner liquid cleaner indiscriminate because they can damage the lining of the protective function to prevent the rays bouncing. If there are no special cleaning fluid, preferably using water mixed with a little soap.

Keyboard
1. Dirt in between the buttons
The location of the keyboard buttons that coincide with each other a bit interrupted often cause dust, dirt, and crumbs lurking on the sidelines of a button. Cleaning the Keyboard Vacuum cleaner is a suitable tool for cleaning dirt and crumbs hidden in cracks crack Keyboard. Another alternative is to spray the air between the keys. Do not shake up and knocked on the keyboard with hard because it can damage it.
2. Liquid doused
Spilling drinks to the keyboard can happen to anyone. When that happens, immediately turn off the notebook, place the tissue paper / cloth napkin over the keyboard and turn it to drain fluid and prevent enter into other components.
In some specific brands such as Acer NB, NB construction allows fluid to flow into the base without damaging the circuit.

Wednesday, August 25, 2010

Tips to Reduce the temperature of the Mainboard & CPU

PC Maintenance should include not only software running virus and spyware scans and defragmenting your hard drive. Protect your computer innards are equally important. Protect your computer hardware starting with peace of mind. Too much heat generated from your computer can cause stability problems and damage internal components. Keeping the central processing unit, or CPU, mainboard and cool is very important to preserve and protect the performance of PC hardware.

Desktop Placement
Where your computer is an important role in how to get hot. Keep your computer in a well ventilated area. Avoid putting in a closed area because this will reduce air flow to the computer. Leave enough space behind the PC to allow air out of the back. Also, put your computer in a cooler part of the office or home will help keep the temperature down.

CPU Fan
Shares including the CPU coolers are often not enough to keep this unit cool. If you're running a PC with other high heat generating components, such as graphics cards, the temperature will rise and make the stock CPU cooler is not effective. Replace your CPU cooler with fan and heat sink from another vendor. Make sure that the new CPU cooler will fit with the type of processor socket before you buy.
 
Case Fan
Adding a new component can require additional cooling options. Case fans easy to install and can keep your system cool at low cost. Some computer cases have only a few places where the case fans can be installed. Adding more fans than capable of holding the case will require some modification.
Please note that only add case fans will not guarantee a cooler. Which lies just a little fan will keep the computer more or less cold than many fans are placed.

Airflow
After the smooth flow of air through your computer case needs. Computers need a cold air flow into and effective so that ventilation air can escape the heat. As mentioned earlier, more fans are not always better. Maximize air flow with fans in the front sucking air while the fan hot air out the rear flow.
 
Water Cooling
Water cooling is another method of keeping your computer cool. Cooling block can be attached to components such as CPU, mainboard, hard drives and graphics cards. Water cooling systems can be expensive and require constant maintenance. Although difficult to install and maintain, water cooling can keep the temperature down, especially when overclocking, or push your system to its limits

Tuesday, August 24, 2010

How to Take Care of Optical Mouse

Caring for an optical mouse different from the care of the ball mouse, when mouse is usually once a week to open soccer ball and cleaned using alcohol liquid manure which sticks on the ball and swivel wheels. But if my optical mouse is more simple try to guess your mouse around the mouse pad the same condition it was dry and clean the rubber buffer 4 for the mouse at the bottom. Even better you prepare cotton bud and clean the optic with alcohol liquid.

Optical Mouse is a mouse that uses optical lenses to use them. Same equipment used by the mouse ball, but the way her treatment:
1. Open the mouse and remove the existing components in it,
2. Clean the components from dust,
3. If after cleaning the mouse is still broken , bring the mouse to an expert trouble shooting the mouse, but if you can do it yourself then do it.

Solution if the optical mouse pointer moving the motion itself:
1. See the base used for mouse pad, If a lot of different colors who try to exchange with one color of paper for example hvs paper
3. If you're still rocking also try to unplug the mouse connector and then plug again
4. If the mouse pointer still move by itself, try to replace your mouse with other mouse
5. If your mouse still rocking, then computer must be reinstalled because there is an error in the Windows System.

Friday, August 13, 2010

Checking and Correcting Dead Pixel LCD Monitor

For users of LCD monitors, LCD for some time after use, sometimes the dots appear on the screen can not display colors properly. Point on the screen is only visible [light] the same thing as changing the monitor display though. So that often reduces the display quality. Dot in the damaged screen is normal with

Dead Pixel or Stuck Pixel well. How do I know it, and if it appears, is there any way to fix?

Knowing / Check for the existence of Dead Pixels

In essence to check the existence of Dead Pixel easy enough, sometimes we can immediately see on the screen, because of the color pixel that is always the same point with the display screen / all monitor image. Or by making a full picture of the screen with one color only, such as black or white. This way if there is a dead pixel would be clearly visible. If you want to use the software (plus extra features), one can use a free program PixelRepairer. This software has several features, among others:
  • Help find dead pixels
  • Can help repair dead pixels
  • Repair dead pixels can be run without having to stop working with computers
  • Requires no installation (portable)
  • Can handle multiple monitors are installed on your computer

Looking for Dead Pixels

To find the dead pixel with this software, follow the following steps:
  1. Clean the monitor
  2. Run PixelRepairer
  3. If the search button is not active, activate the Search button, the existing loop drawings, top left
  4. If more than one monitor connected, select the one
  5. Choose one color in the color list (Pattern)
  6. Click the Enable button, thus changing the monitor display one color or a pattern.
  7. Check the monitor, if there is a point / pixel having a color other than the selected color, means that there are dead pixels on the monitor
  8. To exit, right click the screen or press the ESC keyboard
If the dead pixel is found on a monitor, remember its position so that it can be done following corrective measures.

Dead Pixel Repair

When the monitor is found dead pixel or a pixel is damaged, can be tried to make improvements to the software above. Steps were as follows (the following steps executed if step Find Dead Pixels previously been executed and the dead pixel already in the know location):
  1. Run PixelRepairer
  2. Click the Repair button (the button / picture second from top)
  3. Add the areas of improvement, with a click on the Add button, so the small box will appear called "Repairer". We can adjust the size by sliding size option at the bottom.
  4. Drag or slide the little box "Repairer" to a position where there are dead pixels
  5. Select operation mode: noise or solid. If the noise does not succeed, try again by selecting a solid option.
  6. Select the size of repair, should include the area contained dead pixel
  7. Frequency set equal to the frequency of the monitor. If not changed, usually frequency 60Hz
  8. If Dead pixels are in some places, add Area "Repairer" other
  9. Minimize the program window
  10. Wait about an hour. Can be use the computer as usual.
Accidental damage is permanent pixel, because it was severe enough that can not be corrected anymore. So that this software does not always guarantee 100% successful. Besides can be used for LCD monitors, can also be used for Plasma TV Pixel. This software runs on Windows operating system and licenses Freeware
(Free). Download PixelRepairer_2.0.0.zip (754 KB) or 7zip version PixelRepairer_2.0.0.7z (560 KB)

Wednesday, August 11, 2010

Tips, When your printing documents become stuck


For those of us who frequently print documents with the printer or whatever, sometimes stubborn problems of his process of printing. When printing several documents, then the first document failed (error) is usually the printer stops printing, the queue data will not be removed and sometimes the computer must be restarted to begin printing again. 
The process can print to the printer stopped for various reasons, such as data corruption when sent to a printer or printing process that is incomplete in send applications but can not be deleted. So that the print queue will not be able to run next. This is usually known by the term stalled / Stuck Print Job. 
To overcome these problems, we can remove the list of queues that can not be printed (print) with the manual method as follows: 
  1. Open the Control Panel> Administrative Tools> Services 
  2. Search "service" whose name and then right-click Print Spooler and select Stop. Do not be closed before the window Service 
  3. Open the Windows system folder, usually in the C: \ WINDOWS \ system32 \ spool \ Printers 
  4. Delete all files in the folder. Usually file with the extension *. SPL and *. SHD 
  5. After all removed, such as step number two, but right-click Print Spooler and select Start 
  6. Repeat the process of printing documents 

In addition to the above ways, there is another easier way, using software called stalled Printer Repair. With stalled Printer Repair, we can delete all the queues at the printer list, then repeat the printing process without having to restart the computer. Some features of this application include: 
  • Detect stalled Print Jobs 
  • Delete all queue that can not be in print. 
  • Applications are portable, no need to install and do not write in the registry 
Stalled Printer Repair (346 KB). How to use it very easily. After downloading, simply unzip and run the program. If there is a queue in the print it will appear on the program. Then if you want to delete all the queue, click Purge Print Jobs. Furthermore, we can repeat printing process.
Download Stalled Printer Repair here.

Thursday, August 5, 2010

How To Maintain Flashdisk to be More Durable

No doubt that the flash media is now most often used to save the data very easy to carry everywhere. But few who watched this flash problem. Perhaps because of the capacity to large (Gigabyte), then all data is entered, and every moment is installed in a computer is like a mini hard drive. In fact there are hundreds of content not only data, but thousands of data.

Few people know that the flash has a life, like fluorescent lamps which have a life (eg hold until 5000 hours). Nor flash. But what age the size of the flash? How to use flash to make it more durable / durable? what important things to note about the flash?

Some of the things that became characteristic Flashdisk

Some things may need to know about the flash (pure USB Flash disk, not MP3/MP4):
    * USB Flash Disk can only be activated if there is electrical current that can be obtained via the USB port.
    * Some Flash Disk or currents require greater power than others, so sometimes it must be plugged directly on the motherboard port (without cable connection and not a port on the front) to be detected.
    * Flash Disk can not be read if the cable used was too long, because the current is usually less powerful.
    * Flash Disk has the age / lifetime, like 100 000 read / write or resistance to 10 years.
    * Read access speed is faster than writing in the flash. For example to read 16 MB / s while writing 4 KB / s (one and others vary)
    * File system commonly used is FAT or FAT32, because it can be accessed almost anywhere that supports the USB port. Though can be formatted in accordance with the operating system type, such as NTFS.
    * Defragment files on flash is not needed and did not influence the speed of access, because flash is using a type of Random Access Memory.

How to secure the data therein?

Seems the only way to encrypt data in the flash disk. Although nowadays when buying a flash disk is included software that can lock (lock), but still can not open an existing computer software. USB Flash disk is not damaged although the possibility of wet or even submerged, the origin is dried before being used first.

Tips for Using a more durable Flashdisk

    * Do not save files that are very much into the flash, if possible better in the zip. As more and more to save the file then the process will also write more flash, so its age is also rapidly decreasing.
    * If not very important, avoid directly editing the flash. Alternatively copy the data on your computer, then edited and after returning the copy to Flashdisk.
    * If not worn / used, remove the stick from the computer.
    * Always try to remove the stick from the computer through the "Safety Remove Hardware" and avoid the immediate release when in the process read / write, because it could have been damaged by an electrical current.

Flashdisk with one another has the age and speed vary. One more tips when buying flash, do not just look at the price, but also a guarantee, if more expensive but guarantees little longer, then select a longer warranty.

Wednesday, August 4, 2010

How to improve Windows XP performance

1. Defragment Your Computer - This will place the same files physically closer on the hard disk and will help increase the speed of the load.
  • Click Start, once again, run and then click.Type, "dfrg.msc" into the text field.
  • Click Defrag to start it.

 2. Perform a disk clean.
  • Click start at the bottom left corner, then click run.
  • Type, "cleanmgr.exe" into the text field.
  • Press "OK". It can take a while if you've never done before.

3. Make Windows Load Faster
  • Click Start, then Run.
  • Type 'msconfig' and press enter.
  • Click on the BOOT.INI tab at the top.
  • To the right will have a box labeled Timeout with 30 in it. Change 30 to third.

4. Set Pagefile size
  • Click Start, (Settings), Control Panel, System. (It's like a step above this.)
  • Open the Advanced tab. Click the Settings button under Performance.
  • Now switch to the Advanced tab, then click 'Change' under Virtual Memory.
  • You will see 'Initial Size (MB)' and Maximum size (MB) '.
  • Change 'initial size' with the same value and then click set as a 'Maximum Size'.
  • NOTE: When your computer is consuming your computer's hard drive and use it as RAM, is referred to as a blow. Thrashing is bad for your computer and buy a RAM (not expensive) is far more valuable.